Skip to main content

Show interface IP Address in Windows 10


Commands below work in Windows 10, I think it will also work in Windows 2012.

Displaying or show IP Address in Windows is quite straight forward using ipconfig /all command.

The command has the /all parameter so it will display the IP Address of all the interfaces on the machine.

Display IP Address of a specific interface in Windows via command line using “netsh” tool.

To display the interface IP Address you need to get the interface name.

Typing the command below will show all the interface name and its state whether its connected or disconnected.

     netsh interface show interface

Sample output:
Admin State    State          Type             Interface Name
-------------------------------------------------------------------------
Enabled        Connected      Dedicated        Ethernet
Enabled        Connected      Dedicated        VMware Network Adapter VMnet1
Enabled        Connected      Dedicated        VMware Network Adapter VMnet8
Enabled        Connected      Dedicated        Wi-Fi
Enabled        Disconnected   Dedicated        Ethernet 2

To get the IP Address of a particular interface, type:

Wi-Fi is the name of an interface, replace the parameter with any interface name.

     netsh interface  ipv4  show ipaddresses  Wi-Fi

Sample output:

Address 192.168.169.19 Parameters
---------------------------------------------------------
Interface Luid     : Wi-Fi
Scope Id           : 0.0
Valid Lifetime     : 3h31m50s
Preferred Lifetime : 3h31m50s
DAD State          : Preferred
Address Type       : Dhcp
Skip as Source     : false

The output also shows whether the IP Address was set via DHCP or not.

To display IP Address of all the interfaces using netsh, type:

    netsh interface  ipv4  show ipaddresses

Interface 13: Wi-Fi
Addr Type  DAD State   Valid Life Pref. Life Address
---------  ----------- ---------- ---------- ------------------------
Dhcp       Preferred     3h30m11s   3h30m11s 192.168.169.19

Interface 1: Loopback Pseudo-Interface 1
Addr Type  DAD State   Valid Life Pref. Life Address
---------  ----------- ---------- ---------- ------------------------
Other      Preferred     infinite   infinite 127.0.0.1
Interface 24: Ethernet

Addr Type  DAD State   Valid Life Pref. Life Address
---------  ----------- ---------- ---------- ------------------------
Other      Preferred     infinite   infinite 169.254.0.241

Interface 4: Local Area Connection* 3
Addr Type  DAD State   Valid Life Pref. Life Address
---------  ----------- ---------- ---------- ------------------------
Other      Tentative     infinite   infinite 169.254.231.119

To get more information about the interface, type:

     netsh interface  ipv4 show interfaces level=verbose

Sample output:

Interface Wi-Fi Parameters
----------------------------------------------
IfLuid                                                   : wireless_32768
IfIndex                                                 : 13
State                                                    : connected
Metric                                                 : 25
Link MTU                                          : 1500 bytes
Reachable Time                                 : 19000 ms
Base Reachable Time                        : 30000 ms
Retransmission Interval                    : 1000 ms
DAD Transmits                                  : 3
Site Prefix Length                             : 64
Site Id                                                : 1
Forwarding                                         : disabled
Advertising                                         : disabled
Neighbor Discovery                            : enabled
Neighbor Unreachability Detection   : enabled
Router Discovery                               : dhcp
Managed Address Configuration      : enabled
Other Stateful Configuration              : enabled
Weak Host Sends                                : disabled
Weak Host Receives                           : disabled
Use Automatic Metric                         : enabled
Ignore Default Routes                         : disabled
Advertised Router Lifetime                 : 1800 seconds
Advertise Default Route                      : disabled
Current Hop Limit                               : 0
Force ARPND Wake up patterns        : disabled
Directed MAC Wake up patterns       : disabled
ECN capability                                   : application

This command shows more details about a specific interface which  includes gateway, IP address, subnet mask, DNS and interface metric.

          netsh interface  ipv4  show config name="Wi-Fi"

Configuration for interface "Wi-Fi"
    DHCP enabled:                                              Yes
    IP Address:                                                    192.168.170.19
    Subnet Prefix:                                                192.168.1.0/24 (mask 255.255.255.0)
    Default Gateway:                                           192.168.170.254
    Gateway Metric:                                             0
    InterfaceMetric:                                              25
    Statically Configured DNS Servers:               81.82.83.84
    Register with which suffix:                             Primary only
    WINS servers configured through DHCP:      None



Cheers.. Enjoy..

=================

Catholic Rosary Guide  for Android:
Pray the Rosary every day, countless blessings will be showered upon your life if you recite the Rosary faithfully. 
https://play.google.com/store/apps/details?id=com.myrosaryapp

http://quickbytesstuff.blogspot.sg/2014/09/how-to-recite-rosary.html

Divine Mercy Chaplet Guide (A Powerful prayer) BFF = Be Filled Faith:


Multiplication Table for early learners

https://play.google.com/store/apps/details?id=com.TableMultiplication
Labels:

Comments

Post a Comment

Popular posts from this blog

WMIC get computer name

WMIC get computer model, manufacturer, computer name and  username. WMIC is a command-line tool and that can generate information about computer model, its manufacturer, its username and other informations depending on the parameters provided. Why would you need a command line tool if there’s a GUI to check? If you have 20 or 100 computers, or even more. It’s quite a big task just checking the GUI to check the computer model and username. If you have remote computers, you need to delegate someone in the remote office or location to check. Or you can just write a batch file or script to automate the task. Here’s the code below on how get computer model, manufacturer and the username. Open an elevated command prompt and type:     wmic computersystem get "Model","Manufacturer", "Name", "UserName" Just copy and paste the code above, the word “computersystem” does not need to be change to a computer name. A...
Post a Comment
Read more

Print error 016-799 - Fuji Film Xerox

016-799 Fuji Xerox or Fuji Film print error code. That shows a description error as “Print instruction Fail detected in decomposer.” The error code and error description are alien languages for users and even system administrators who are not familiar with Fuji Xerox error code. The error code is quite simple and easy to fix, if the job print goes to the printer but print out doesn’t come out. So, basically the print job was received by the printer, but the printer just doesn’t know what type of paper or what size to use or which tray to utilize for the print out. In some instances, this is just a paper mismatch but the error description; if using Windows 10 to print does not exactly points to what is the issue. First thing to check, is the paper size selected by the user to print. Example, if the printer configuration is A3 and A4 sizes only. But then the person printing the file accidentally chooses “A4 Cover” then this error 016-799 will occur. ...
6 comments
Read more

How to check office version from command line

The are quite a few ways to check office version it can be done via registry, PowerShell or VBScript and of course, good old command line can also do it. Checking Windows office version whether it is Office 2010, Office, 2013, Office 2016 or other version is quite important to check compatibility of documents; or just a part of software inventory. For PowerShell this simple snippet can check the office version: $ol = New-Object -ComObject Excel.Application $ol . Version The command line option will tell you where’s the path located; the result will also tell whether office is 32-bit, 64-bit and of course the version of the office as well. Here’s the command that will check the office version and which program directory the file is located which will tell whether it’s 32-bit or 64-bit. Command to search for Excel.exe: DIR C:\ /s excel.exe | find   /i "Directory of"  Above command assumes that program files is on  C: drive. Sample O...
Post a Comment
Read more